​​The SJ-10 SpeakerJumpers use 10 gauge (99.99999%) ultra-pure copper conductors and the SJ-14 Speaker jumpers uses 14 gauge  (99.99999%) ultra-pure copper conductors, both with an internal damping filament placed among the copper strands which assists in the low noise floor of the jumper. The SJ-10 and SJ-14 jumpers are terminated with Furutech Rhodium spade connectors or straight banana connectors. As with all our cables the jumpers also undergo a  chemical treatment prior to the finished assembly and conditioned on our cable cooker. The SJ-10 and SJ-14 Jumpers are available in 6 ior ten inch lengths which is measured from connector tip to connector tip, additional lengths are vailable on request​. 

The SP-10 Reference is our top of the line speaker cable. Its ideal for a wide range of speakers, and is excellent with either solid state or tube amplification. The SP-10 Reference uses (99.99999%) ultra-pure copper 10 gauge conductors per leg with an internal damping filament placed among the copper strands which assists in the low noise floor of the cable. The SP-10 Reference cable also uses an EMI absorbing material between the conductor insulation and the inner sleeve which addresses EMI contamination. The SP-10 speaker cables are well balanced sound wise, they're liquid, dynamic, organic, and present all of the fine micro-details without highlighting any part of the audio spectrum which all too often is the case with cables.


The SP-10 Reference series speaker cables are available in any length and terminated with Furutech Gold spade and/or banana connectors. Prior to the finished assembly all conductors and connectors are chemically treated and, once completed, they undergo 100 hours of conditioning on our cable cooker. This pre-conditioning process helps initialize the dialectic and copper conductor material stabilization process that's associated with cables. Once installed, they will require approximately 125 hours of actual use to complete the settling process. We also provide a mix of connector types at both able ends to accommodate every binding post configuration.

  SP-10 REFERENCE SERIES SPEAKER CABLES

The PC-1 Reference Power Cord conductors (hot, neutral, ground) are chemically treated prior to the finished assembly and, once completed, they undergo 100 hours of conditioning on our cable cooker. This pre-conditioning process helps initialize the dialectic and copper conductor material stabilization process that's associated with cables. This differs slightly from just installing the cables in a system and letting them settle. Once installed, they will require approximately 150-200 hours of actual use to complete the settling process.

The PC-1 Reference Power Cord is our top of the line power cord, ideal for any source component, amplifier or power conditioner application. The Reference power cords use (99.99999%) ultra pure copper 10 gauge conductors, copper shield for superior noise rejection, EMI absorption and conductor damping filaments, and terminated with Furutech Carbon Fiber NCF connectors. The PC-1 Reference power cord is a reasonably flexible power cord, there are no unnecessary filler materials being used making them appear larger than what they are or making them difficult to use. The PC-1 Reference power cord delivers exceptionally neutral sound, tight and tuneful low level details with an engaging mid range with clean and extended highs.

PC-1 Reference power cord

  SJ-10 six inch jumpers $300 per stereo set        SJ-10 ten inch jumpers $350 per stereo set
  SJ-14 six inch jumpers $200 per stereo set        SJ-14 ten inch jumpers $250 per stereo set

                                                                     (Additional lengths are available upon request)

The PC-3 Reference Power Cord offers excellent value and uses the same wire and construction as our PC-1 & PC-2 Reference Power Cords but uses Furutech FI-11 connectors. Its ideal for any source component, amplifier or power conditioner application. The PC-3 Reference power cords use (99.99999%) ultra pure copper 10 gauge conductors, copper shield for superior noise rejection, EMI absorption and conductor damping filaments, and terminated with Furutech FI-11 N1 (R) connectors. The PC-3 Reference is a reasonably flexible power cord, there are no unnecessary filler materials being used making them appear larger than what they are or making them difficult to use. The PC-3 delivers a well rounded neutral sound, tight and tuneful through out with an engaging mid range with clean and extended highs.


The PC-3 Reference Power Cord conductors (hot, neutral, ground) are chemically treated prior to the finished assembly and, once completed, they undergo 100 hours hours of conditioning on our cable cooker. This pre-conditioning process helps initialize the dialectic and copper conductor material stabilization process that's associated with cables. This differs slightly from just installing the cables in a system and letting them settle. Once installed, they will require approximately 150-200 hours of actual use to complete the settling process.

The FPC-200 Reference Filtering Power Cord is ideal for any source component or amplifier where passive filtering is desired. The FPC-200 power cord uses (99.99999%) ultra pure copper 10 gauge conductors, copper shield for superior noise rejection, EMI absorption and conductor damping filaments, as found in our other power cords. The FPC-200 power cord is terminated with Furutech FI-28 (R) male ac connectors and Furutech FI-68 (R) IEC connectors, a sophisticated, luxuriously made passive power filtering IEC connector devise that eliminates many common problems caused by contaminated electrical power lines. It protects against distortion caused by ground noise, voltage spikes and sags, high frequency power supply noise from other components in your own system, and finally high-frequency digital noise emanating from processors and digital interconnects. The PC-200 power cord does not restrict or soften dynamics, it delivers exceptionally neutral sound, tight and tuneful low level details with an engaging mid range with clean and extended highs.


The FPC-200 power cord conductors (hot, neutral, ground) are chemically treated prior to the finished assembly. The FPC-200 undergoes a slightly different conditioning process as used in our other power cords and speaker cables, Once we have completed the wire build and terminate the FI-28 (R) male connector only, the IEC end of the power cord is then temporarily terminated to a custom made IEC adapter leaving the FI-68 IEC filtering connector un-installed during the conditioning process, once the 100 hour conditioning process is completed, the custom made IEC adapter is removed and the Furutech FI-68 IEC is terminated, completing the power cord build. This pre-conditioning process helps initialize the dialectic and copper conductor material stabilization process that's associated with cables. This differs slightly from just installing the cables in a system and letting them settle. Once installed, they will require approximately 400 hours of actual use to complete the settling process. Due to the IEC filtering devise being used on the FPC -200 power cord we do not recommend using a burn in devise as it can result in damage to the IEC filter.   

The SP-14 Reference speaker cables are identical in design and configuration to our SP-10 speaker cables except it uses (99.99999%) ultra-pure 14 gauge copper conductors with the same internal damping and EMI materials. The SP-14 is ideal for small to medium size speakers and is excellent with either solid state or tube amplification. The SP-14 speaker cables are well balanced sound wise, they're liquid, dynamic, organic, and present all of the fine micro-details without highlighting any part of the audio spectrum which all too often is the case with cables.

The SP-14 Reference series speaker cables are available in any length and terminated with Furutech Rhodium spade and/or banana connectors. Prior to the finished assembly all conductors and connectors are chemically treated and, once completed, they undergo 100 hours of conditioning on our cable cooker. This pre-conditioning process helps initialize the dialectic and copper conductor material stabilization process that's associated with cables. Once installed, they will require approximately 125 hours of actual use to complete the settling process. We also provide a mix of connector types at both cable ends to accommodate every binding post configuration.

SJ-10 JUMPERS and SJ-14 JUMPERS

​​​​The PC-2 Reference Power Cord follows in design and construction of our PC-1 Reference Power Cord and offers performance levels close to the Reference but at a slightly lower price point. The PC-2 power cord is ideal for any source component, amplifier or power conditioner application. The PC-2 power cord uses (99.99999%) ultra pure copper 10 gauge conductors, copper shield for superior noise rejection, EMI absorption and conductor damping filaments, and terminated with Furutech FI-28 (R) connectors. The PC-2 is extremely effective at delivering a well balanced and natural sound. The lower registers are well articulated with an engaging mid range and extended, smooth top end. 

PC-2 REFERENCE POWER CORD

1.0 Meter $695        1.5 Meter $895        2.0 Meter $1095        2.5 Meter $1295        3.0 Meter $1495
​                                                    (Additional lengths are available, add $200 per 1/2 meter (stereo pair)

1.0 Meter $995        1.5 Meter $1095        2.0 Meter $1195        2.5 Meter $1295        3.0 Meter $1395

           (Additional lengths are available, add $100 per 1/2 meter)       (Optional 20 amp IEC  FI-52 CF NCF add $75.00) 

SP-14 REFERENCE SERIES SPEAKER CABLES​

1.0 Meter $695      1.5 Meter $795      2.0 Meter $895       2.5 Meter $995       3.0 Meter $1095

                                                 (Additional lengths are available, add $100 per 1/2 meter)

The PC-2 Reference Power Cordconductors (hot, neutral, ground) are chemically treated prior to the finished assembly and, once completed, they undergo 100 hours hours of conditioning on our cable cooker. This pre-conditioning process helps initialize the dialectic and copper conductor material stabilization process that's associated with cables. This differs slightly from just installing the cables in a system and letting them settle. Once installed, they will require approximately 150-200 hours of actual use to complete the settling process.

      Copyright  2017 Unity Audio Design All rights reserved.

Introducing the FPC-200 Filtering Power Cord

1.0 Meter $395        1.5 Meter $495        2.0 Meter $595        2.5 Meter $695        3.0 Meter $795
​                                           
(Additional lengths are available, add $100 per 1/2 meter)

Call 925-425-0450

1.0 Meter $395        1.5 Meter $495        2.0 Meter $595        2.5 Meter $695        3.0 Meter $795
​                                               (Additional lengths are available, add $100 per 1/2 meter (stereo pair)

PC-3 REFERENCE POWER CORD

1.0 Meter $595        1.5 Meter $695        2.0 Meter $795        2.5 Meter $895        3.0 Meter $995

​            (Additional lengths are available, add $100 per 1/2 meter)        (Optional 20 amp IEC FI-32 add $65.00)